What you will learn?

Medium RPC with Drone Maintenance & DaaS Training

Sr. No.	Subject	Duration
1	Stakeholders and their Laws, Drone Rules 2021	1:30 Hours
2	Basic Principles of Flight	1:00 Hours
3	ATC Procedures and Radio Telephony	1:15 Hours
4	Fixed wing Operations and Aerodynamics	1:15 Hours
5	Rotorcraft Operations and Aerodynamic	1:30 Hours
6	Hybrid Operations and Aerodynamics	0:30 Hours
7	Weather and Meteorology	1:15 Hours
8	Drone Equipment and maintenance	1:30 Hours
9	Risk Assessment and Analysis – Safety Management / TEM	1:30 Hours
10	Payload installation and utilization	1:15 Hours
11	Intro to Drone Data and Analysis	1:30 Hours

Sr. No.	Subject	Duration
Assesment	Theory Test - Final	0:40 Hours
Ex. 1, 2, 3	Introduction to flight simulator, simulator familiarization, control check, pre-flight checks, Take off, cruise.	0:30 Hours
Ex. 4, 5, 6	Approach, go-around and landing, post flight checks, Cruise and Turns, Climbing and Climbing Turns, Descend and Descending Turns	0:30 Hours
Ex. 7, 8	Disorientation and Recovery, Circuit Flying – Rectangle/ Square/ Circle / Orbit, Flying – Figure of 8	0:30 Hours
Ex. 9	Gimbal Controls (Pan, tilt and zoom	0:30 Hours
Ex. 10	Night flying	0:30 Hours
Ex. 11	Abnormal/ Emergency procedures	0:15 Hours
Ex. 12	Sim Test	0:15 Hours

Sr. No.	Subject	Duration
Ex. 1	Intro to Digital Sky platform	0:30 Hours
Ex.2	RPAS familiarization and Safety briefing	0:15 Hours
Ex.3	Introductory flight where the student experiences sensitivity of controls and learning the orientation of the RPA.	0:15 Hours
Ex.4	Takeoff, Climbing, descending and maintaining height.	0:15 Hours
Ex.5	Basic Controls: Pitch, Roll and Yaw	0:15 Hours
Ex.6	Flying in a disorientation scenario and to recovery from the same.	0:15 Hours
Ex.7	Progress Check – Multirotor	0:15 Hours
Ex.8	Level turns in both directions	0:15 Hours
Ex.9	Climbing and descending turns	0:15 Hours
Ex.10	Left and right square circuits patterns	0:15 Hours
Ex.11	Flying in circles	0:15 Hours
Ex.12	Flying in figure of 8	0:15 Hours
Ex.13	Mission Planning and Instrument Flying	0:15 Hours
Ex.14	Auto Mission and Flight	0:15 Hours
Ex.15	Night Flying	0:15 Hours
Ex.16	Abnormal/ Emergency procedures	0:15 Hours
Ex.17	Final Test – Multirotor	00:20 Hours

Sr. No.	Subject	Duration
1	Safety: DGCA Rules and Regulations, Regulatory Overview	20:00 Hours
2	Drone Fundamentals & Assembly Basics
3	Drone Types: Multirotor, Fixed-Wing, Hybrid
4	Key Components: FC, Motors, ESCs, GPS, Frame
5	Bill of Materials (BoM), Safety Tools & Protocols
6	Basic Flight Principles
7	Electronics, Wiring & Configuration
8	Component Identification
9	Tool Handling & Mock Drone Frame Setup
10	Troubleshooting & Battery Management
11	Drone as a Service (DaaS)
12	Capstone Project & Final Evaluation
13	Final Theory Test

Sr. No.	Subject	Duration
1	Assembly session for Basic Assembly of Frame & Calibration	04:00 Hours

Sr. No.	Subject	Duration
1	RPAS Familiarization, Pre-Flight Checks & Safety Briefing	01:15 Hours
2	Introductory Flight (Orientation & Control Sensitivity)
3	Manual Take-off & Hovering
4	Auto Mission & Flight, Mission Planning & Instrument Flying